
ESD
CONTROL PRODUCTS ( Testing/Measuring Instrument )
Electro Static
Discharge (ESD) is the momentary and unwanted electric current that
flows between two objects at different electrical potentials. It may
cause damage to electronic equipment causing fire, explosion, EMI, RFI,
heat, light and sound. Immaculately engineered to the height of
perfection using cutting edge technology, our ESD control products
provide efficient solutions to our clients' various ESD problems. We also
supply ESD tester, esd mat tester, esd wrist strap tester,
esd measuring devices, esd measuring instruments, esd testing meters, surface resistivity
meters and all other ESD testing instruments.
GROUND MONITOR -(Model: GM-01)
Proper grounding is crucial for safe and uninterrupted operation. In
critical environments a broken ground connection may result in
personnel exposure to dangerous voltages, equipment lock-up or
malfunction, and ESD damage to sensitive components.

This Bench Top Instrument is designed to
neutralize your ESD work-station or ESD protected area with a stream of
ionized air. It does what Wrist straps, conductive mats & ESD
Laminates cannot doi. e remove static charges from nonconductive
objects and surfaces.
Ground Monitor shows which are being monitored with an OK or Fail
status of the ground, In addition it is ideal for use as a grounding
point for bench / floor mats and personnel grounding.
Specification:
| Resistance |
Built
in 1 meg-ohm resistor for personnel safety |
| Indications |
|
| Pass |
Green
LED |
| Fail |
Audible
alarm |
| Input
power |
AC230V
/ 50 Hz |
| Dimensions |
82 x
55 x 56 mm (With Plug Pins) |
| Weight |
75 Gms |
| Warranty |
One
Year |
|
 |
WRIST STRAP TESTER - (Model: WST-01)
Wrist strap is the first line of defence against electrostatic charges
builds up on the human body. It is designed to carry away this charge
as soon as it is generated. At the same time wrist strap must remain
electrically safe for the user. Thus, it is important to test every
wrist strap regularly.

In order to protect the sensitive electronic
components the maximum wrist strap resistance should not be more than
10 Meg ohms on the other end, the resistance should not be less than
0.75 Meg ohms as protection to the wearer from dangerous level of the
voltage and current flow.
The wrist strap tester checks these parameters under actual operating
conditions with the strap on the wrist. It clearly indicates weather or
not the resistance of the wrist strap system including the wearer is at
least 0.75 Meg ohms and not more than 10 Meg ohms respectively.
Specification:
| GREEN
Pass |
Resistance
Between 0.75 to 10 Meg Ohms |
| RED
Fail |
Resistance
below 0.75 OR above 10 Meg Ohms |
| Audible
Alarm |
Sounds
for open OR FAIL condition. |
| Battery
Status |
By
Dual Color LED |
| Test
Actuation |
By
pressing metal sensor plate |
| Accuracy |
+/- 10% |
| Power
Supply |
9 Volt
Battery |
| Dimensions |
135 x
70 x 25 mm |
| Weight |
App.
135 Gms with battery |
| Calibration |
Recommended
every 12 months |
| Warranty |
One
Year |
| Optional |
Instruction
Board, Carry Case & Door Access systems |
|
 |
OPTIONAL FOR WST-01
The WST-01 can be wall mounted outside the ESD protected area using the
INSTRUCTION board.
The WST-01 has the special features of accessing the ESD protected area
door by using Electro Magnetic Lock.
COMBO TESTER -(Model: CT-01)
The Wrist strap Cum Dual Footwear tester is a jig type arrangement to
test the validity of ESD Wrist strap & foot wears. The
instrument measures Independent test simultaneously for right foot,
left foot and wrist strap at the same time. Other Footwear testers can
only measure two foot at a time, or the combined resistance of both
foot. The wrist strap cum Dual Foot Tester reduces the testing time by
half, and offers the operator a visual and audible measurement of Pass
or fail of both foot and wrist strap before entering the EPA.
Operation of Wrist Strap
Connect the wrist strap cord to the instrument with the strap on the
wrist; press gently on the metal sensor of the wrist strap tester. The
instrument comes on automatically when this is done. The operator can
check whether the resistance of the wrist strap falls within the
acceptable range (0.75 to 10 Meg ohms), This is indicated by green
(pass) LED lighting up.
Operation of Foot Wears:
Simply stand on the two stainless steel footprints on the foot plate
and push the Dual foot wear tester press to test button. The instrument
comes on automatically when this is done. The operator can check
whether the resistance of the Foot wears falls within the acceptable
range of 0.75 to 35/100 Meg ohms, this is indicated by green (pass) LED
lighting up.
Specification:
| Wrist
Strap PASS Range |
0.75
to 10 Meg Ohms |
| Foot
Wears PASS Range |
0.75
to 35/100 Meg ohms |
| Indications |
Pass -
GREEN LED LOW & High fail - RED LED with Buzzer sound |
| Test
Actuation |
By
pressing metal sensor plates |
| Power
Supply |
9 Volt
Rechargeable Battery |
| Battery
Status |
By
Dual Color LED. |
| Dimensions |
Instrument:
160 x 95 x 40 mm Foot plate: 470 x 360 mm Height: 1000 mm |
| Weight |
5 Kg |
| Calibration |
Recommended
every 12 months |
| Warranty |
12
Months only for Instrument |
| Accessories |
12V
Charger & Instruction manual |
|
 |
Note: The Company
reserves the rights to change the specification or design without prior
notice.
COMBO TESTER WITH ACCESS SYSTEMS
The Wrist strap Cum Dual Footwear tester is a jig type arrangement to
test the validity of ESD Wrist strap & foot wears. The
instrument measures Independent test simultaneously for right foot,
left foot and wrist strap at the same time. Other Footwear testers can
only measure two foot at a time, or the combined resistance of both
foot. The wrist strap cum Dual Foot Tester reduces the testing time by
half, and offers the operator a visual and audible measurement of Pass
or fail of both foot and wrist strap before entering the EPA.
Operation of Wrist
Strap
Connect the wrist strap cord to the instrument with the strap on the
wrist; press gently on the metal sensor of the wrist strap tester. The
instrument comes on automatically when this is done. The operator can
check whether the resistance of the wrist strap falls within the
acceptable range (0.75 to 10 Meg ohms), This is indicated by green
(pass) LED lighting up.
Operation of Foot Wears:
Simply stand on the two stainless steel footprints on the foot plate
and push the dual foot wear tester press to test button. The instrument
comes on automatically when this is done. The operator can check
whether the resistance of the Foot wears falls within the acceptable
range of 0.75 to 35/100 Meg ohms, this is indicated by green (pass) LED
lighting up.
The CT-02 has three optional
security systems to the personnel before entering EPA as given below: -
Option-1
Electro Magnetic Lock: Person before entering the
EPA, need to test their Wrist Strap/ESD foot wear. If the resistance of
the Wrist Strap/ESD foot wear is within acceptable range then the door
is opened by the release of the Electro magnetic lock of the door.
Option-2
Slim Tripod Turnstile: Person before entering the
EPA, need to test their Wrist Strap/ESD foot wear. If the resistance of
the Wrist Strap/ESD foot wear is within acceptable range then the Slim
Tripod Turnstile is gets unlocked to move.
Option 3
Retractable Flap Barrier: Person before entering the
EPA, need to test their Wrist Strap/ESD foot wear. If the resistance of
the Wrist Strap/ESD foot wear is within acceptable range then the
retractable Flap Barrier is gets opened to move.
Specification:
| Wrist
Strap PASS Range |
0.75
to 10 Meg Ohms |
| Foot
Wears PASS Range |
0.75
to 35/100 Meg ohms |
| Indications |
Pass -
GREEN LED LOW & High fail - RED LED with Buzzer sound |
| Test
Actuation |
By
pressing metal sensor plates |
| Accuracy |
+/- 10% |
| Power
Supply |
12v
Charger for Charging the CT-02 |
| Battery
Status |
By
Dual Color LED. |
| Dimensions |
Instrument:
160 x 95 x 40 mm Foot plate: 470 x 360 mm Height: 1000 mm |
| Weight |
5 Kg |
| Calibration |
Recommended
every 12 months |
| Warranty |
12
Months only for Instrument |
|
 |
Note: The Company
reserves the rights to change the specification or design without prior
notice.
ANALOGUE FOOT WEAR
TESTER (Model: AFT-01)
ESD foot wear is also the first line of defence against electrostatic
charges build up on the human body. It is designed to carry away this
charge as soon as it is generated. At the same time foot wear must
remain electrically safe for the user. Thus, it is important to test
every foot wears regularly.
In order to protect the sensitive electronic components the maximum
foot wear resistance should not be more than 100 Meg ohms. The footwear
tester checks these parameters under actual operating conditions with
operator & foot wear. It clearly indicates the resistance of
the foot wear system including the wearer is less than 100 Meg ohms or
NOT.
The instrumented is designed for measuring the conductive foot wear
also, so the instrument measurement is ranged from 0 to 100 Meg ohms.
For Checking Foot Wear::
Simply stand on the foot plate and press gently on the metal sensor
plate; the instrument comes on automatically when this is done. The
operator can check whether the resistance of the foot wear falls with
in the acceptable range (0 - to 100 Meg Ohms), This is indicated by
Analogue dial.
Specification:
| Range |
0 to
100 Meg Ohms |
| Indications |
Analogue
Dial |
| Test
actuation |
By
Pressing metal sensor plate |
| Accuracy |
+/- 10% |
| Power
Supply |
9 Volt
Rechargeable Battery |
| Battery
Status |
By
Dual Color LED. |
| Dimensions |
|
| Foot
Plate |
21 x
15 Inches |
| Height |
135 x
70 x 30mm |
| Instrument |
12
Months only for Instrument |
| Weight |
Appx
5.0 Kgs |
| Calibration |
Recommended
every 12 months |
| Warranty |
12
Months |
|
 |
Note: The Company
reserves the rights to change the specification or design without prior
notice.
CONTINUOUS WORK
STATION MONITOR (Model: WSM-01)
The Model WSM-01 is designed to continuously monitor the connections of
ESD wrist strap & work surface.
WRIST STRAP: This section continuously monitors the
wrist strap to detect loss of continuity between operator and monitor.
Conditions such as broken coils cords and improper contact with the
skin are detected instantly to alert the operator before serious and
expensive ESD damage can occur. As there is no resistance return path
from the wrist strap, it uses the “capacitive AC pulse principle” to
check if the operator is adequately grounded. The wrist strap section
is automatically activated when wrist strap is plugged in. continuous
monitoring reduces the need for periodic checks and also ensures
greater security.
ESD WORK SURFACE: The work surface is monitored by a
DC Resistive principle and a warning is given in case the surface to
ground resistance exceeds the safe threshold value of 10 Meg ohms.
Specification:
| Pass
Threshold |
under
4 Meg ohms for wrist strap |
|
Under
10 Meg ohms for MAT |
| Indications |
Green
LED for wrist strap PASS |
|
Flashing
Red LED for wrist strap FAIL |
|
Steady
Red LED for mat FAIL |
| Audible
Alarm |
For
Fail modes |
| Input
Power |
12V @
500 ma DC |
| Accuracy |
+/-10% |
| Repeatability |
+/-10% |
| Dimensions |
125 x
65 x 35mm |
| Weight |
175
Gms (with fixing clamp) |
| Warranty |
12
Months |
| Accessories |
Fixing
Clamp |
| Optional |
Grounding
Cords & 12V Adopter |
|
 |
CONTINUOUS WORK
STATION MONITOR (Model: WSM-02)
The Model WSM-02 is designed for continuously monitor the connections
of two ESD wrist strap & work surface.
WRIST STRAP:Two-wrist strap sections continuously
monitor the wrist strap to detect loss of continuity between operators
and monitor. Conditions such as broken coils cords and improper contact
with the skin are detected instantly to alert the operator before
serious and expensive ESD damage can occur. As there is no resistance
return path from the wrist strap, it uses the “capacitive AC pulse
principle” to check if the operators are adequately connected to the
instrument. The wrist strap sections are automatically activated when
wrist straps are plugged in. continuous monitoring reduces the need for
periodic checks and also ensures greater security.
ESD WORK SURFACE: The work surface is monitored by a
DC Resistive principle and a warning is given in case the surface to
ground resistance exceeds the safe threshold value of 10 Meg ohms.
Specification:
| Pass
Threshold |
under
4 Meg ohms for wrist straps |
|
Under
10 Meg ohms for MAT |
| Indications |
Green
LED for wrist strap PASS |
|
Flashing
Red LED for wrist strap FAIL |
|
Steady
Red LED for mat FAIL |
| Audible
Alarm |
For
Fail modes. |
| Input
Power |
+/-10% |
| Accuracy |
+/-10% |
| Repeatability |
|
| Dimensions |
125 x
65 x 35mm |
| Weight |
175
Gms (with fixing clamp) |
| Weight |
Appx
5.0 Kgs |
| Warranty |
12
Months |
| Accessories |
Fixing
Clamp |
| Optional |
Grounding
Cords & 12V Adopter |
|
 |
CONTINUOUS WRIST
STRAP MONITOR (Model: WSM-03)
Wrist Straps are the first line of defense against electrostatic charge
build-up on the human body. They are designed to carry away this charge
as soon as it is generated.
This model WSM-03 continuously monitors the wrist strap to detect loss
of continuity between operator and monitor. Conditions such as broken
coil cords and improper contact with the skin are detected instantly to
alert the operator before serious and expensive ESD damage can occur.
As there is no resistive return path from the wrist strap, it uses the
“Capacitive AC pulse principle” to check if the operator is adequately
grounded. The system is automatically activated when the wrist strap is
plugged in. Continuous monitoring reduces the need for periodic checks
and audits and also ensures greater security.
Specification:
| Wrist
Strap Range |
0 to
100 Meg Ohms |
| Indications |
|
| Pass |
Green
LED |
| Fail |
Flashing
Red LED |
| Audible
Alarm |
For
Fail Mode |
| Input
Power |
12V @
500 ma DC |
| Accuracy |
+/-10% |
| Repeatability |
+/-10% |
| Dimensions |
125 x
65 x 35mm |
| Weight |
175
Gms (with fixing clamp) |
| Warranty |
Recommended
every 12 months |
| Accessories |
Fixing
Clamp |
| Optional |
Grounding
Cord & 12V Adopter |
|
 |
Our Products